4.2.3 Programming the Network Settings
For successful operation of a VoIP network using the V-IPGW16 card, network settings for the PBX at each location must be programmed appropriately. For a detailed discussion of related features, refer to the Feature Manual.
This section details the procedure to program the network settings for the local PBX. After the programming for the local PBX has been done, repeat the procedure for the remote PBX with the appropriate setting values.
The following procedures describe the process of programming the network settings for each numbering method.
Programming for the PBX Code Method
|
1.
|
a.
Under Configuration, click Slot.
b.
Move the mouse pointer over the PBX image of IPCMPR Virtual Slot at the top of the screen.
c.
Click Select Shelf.
d.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
e.
Click Port Property.
|
|
|
Confirm that all ports are in service (INS).
Note
When a V-IPGW16 card is installed, 8 ports (1–8) are available. When two V-IPGW16 cards are installed, 16 ports (1–16) are available.
|
|
2.
|
a.
From the system menu, click CO & Incoming Call.
b.
Click CO Line Settings.
c.
Type the CO Name and assign an unused Trunk Group Number to be used for all IP CO lines.
d.
Click OK.
|
|
3.
|
a.
From the system menu, click System.
b.
Click Numbering Plan.
c.
Click Main.
d.
Click the Features tab.
e.
In the TIE Line Access box, type the dialing number.
f.
Click OK.
|
|
4.
|
a.
From the system menu, click Private Network.
b.
Click TIE Table.
c.
In the Own PBX Code box, type the PBX code of the local PBX in the network.
d.
In the first unused Leading Number box, type the PBX code of the remote PBX in the network.
e.
In the corresponding Trunk Group list, select the number of the trunk group to be used when making calls.
f.
Set the number modification pattern, if necessary.
g.
Click OK.
|
|
5.
|
a.
From the system menu, click Configuration.
b.
Click Slot.
c.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
d.
Click Ous.
You will see a confirmation message.
e.
Click Yes.
f.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
g.
Click Shelf Property.
|
|
6.
|
a.
Click the Outgoing Call tab.
b.
c.
Click OK.
|
|
7.
|
a.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
b.
Click INS.
|
*1
When "En-bloc" is selected, you need to press "#" after dialing the phone number.
Programming for the Extension Number Method
|
|
1.
|
a.
Under Configuration, click Slot.
b.
Move the mouse pointer over the PBX image of IPCMPR Virtual Slot at the top of the screen.
c.
Click Select Shelf.
d.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
e.
Click Port Property.
|
|
|
|
Confirm that all ports are in service (INS).
Note
When a V-IPGW16 card is installed, 8 ports (1–8) are available. When two V-IPGW16 cards are installed, 16 ports (1–16) are available.
|
|
|
2.
|
a.
From the system menu, click CO & Incoming Call.
b.
Click CO Line Settings.
c.
Type the CO Name and assign an unused Trunk Group Number to be used for all IP CO lines.
d.
Click OK.
|
|
3.
|
a.
From the system menu, click System.
b.
Click Numbering Plan.
c.
Click Main.
d.
Click the Other PBX Extension tab.
e.
In the Other PBX Extension Numbering (TIE) box, type a starting digit of destination extension.
f.
Click OK.
|
|
|
4.
|
a.
From the system menu, click Private Network.
b.
Click TIE Table.
c.
In the Leading Number box, type the starting digit of destination extension.
d.
Click OK.
|
|
|
5.
|
a.
From the system menu, click Configuration.
b.
Click Slot.
c.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
d.
Click Ous.
You will see a confirmation message.
e.
Click Yes.
f.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
g.
Click Shelf Property.
|
|
|
||
|
|
6.
|
a.
Click the Outgoing Call tab.
b.
c.
Click OK.
|
|
|
7.
|
a.
Move the mouse pointer over the installed V-IPGW16 card to display the menu of options.
b.
Click INS.
|
*1
When "En-bloc" is selected, you need to press "#" after dialing the phone number.
Note
For details about network parameter settings, refer to the relevant sections of the PC Programming Manual.